Replacing uPVC Window Handles
It is simple to change the handles on windows made of Upvc. It is essential to make sure that the new handle is fitted into the spindle cutouts in the window mechanism.
If the steps below are followed properly, any cockspur handle should fit in most windows. The height of the step of the handle is key.
What to Look for
Many of the windows in the UK come with uPVC handles and, over time, they can begin to show signs of wear and wear and tear. The handle of the window can become loose or difficult-to-operate when this occurs. Anyone who is familiar using a basic hand tool can accomplish this fairly simple job.
The first thing to do is ensure that the handle is firmly connected to the window frame and is in the open position. The next step is to find the fixing pins or screws that keep the handle in place. These are usually located on the inside of the handle. They can be removed using the screwdriver and pliers.
When the handle has become loose It is best to gently pull it away from its hinges. Then, you'll have to locate a replacement handle of the same dimensions and style. This can be done online or at an area DIY store, and should take around five minutes using an screwdriver.
When replacing the handle of a uPVC handle It is crucial to consider the step height. This is the distance between the handle's base and where it is located in the frame of the window. This is usually an average measurement, but it is important to examine the step height of your existing handle before ordering an entirely new one.
There are several sizes depending on the kind of handle. Inline handles are offered for uPVC windows that have centers of 31mm for lugs, while cockspur handles have lug centres of 43mm. Tilt-and-turn handles are commonly found on uPVC Windows. They have a special design that lets the window be slid down to let in air and then turned to fully open the window.
The most common cause of breakage in uPVC handles is that they crack internally instead of breaking off from the base section. This can make them hard to open and therefore it is essential to ensure that any replacement handle you purchase has the same length of spindle that your current one.
Remove the old Handle
Incorrectly installed or damaged window handles can cause your double glazed windows to open or close in a way that isn't correct and may cause them to become stuck. This could be due to many factors, such as general wear and tear on the metal handle or corrosion. In these cases it is essential to replace the window handle as quickly as you can in order to avoid further damage or loss of function.
When replacing the handles on windows made of upvc and handles, it is important to remove the old handles from the window. To do this, begin by taking off the screw that is encased when the handle is in the closed position. Once you have removed that screw, you are able to remove the handle. You can make the job easier by using an electronic screwdriver.
Be aware that screws may be hidden in caps made of plastic. It is best to remove the covers using the help of a Stanley knife. After the old handle has been removed, you should then examine the square cut out at the base of the handle to ensure that the new window lock handles are compatible with it. This is important as you'll need to measure the length of the spindle of the old handle to make sure it is in line with the size of the window mechanism and the handle spindle that has been cut out.
The various types of upvc window handles are: Espag handles, which feature a central screw that can turn left or right; Cranked handles that have two screws and are used on tilt and turn windows made of upvc as well as Spade handles, that have an arm that is flat and can be placed on either side of the window. Once you have found a suitable replacement, it is simply a case of screwing the handle in place and making sure that the spindle is placed into the lock mechanism. Once that is done then it is time to secure it to the window frame and your replacement window handles made of upvc must be secure.
Take a measurement of the Spindle
If you need to replace a upvc handle that has fallen, it's likely the spindle holding it in place is damaged or is loose. In some instances, it can be fixed by using pins or screws to tighten it. In some instances it might be necessary to replace the handle. There are a few different kinds of window handles made from upvc. There are three kinds of handles: inline espagnolette cockspur, and tilt-and-turn. Each handle type has its own method for installing and replacing the handle.
Before purchasing a replacement handle it is essential to know the size of the handle that is currently in use. This will ensure that the handle will fit the window properly and be the correct size. Luckily, all handles conform to industry standards for sizing, so it's fairly easy to find the right size.
To measure the size of the handle, turn the window to the open position. You should be able see the dimensions of the pin or screw that holds the handle. Then, use a ruler or tape measure to determine the length of the spindle. Once you know the length of your spindle, it is possible to purchase a replacement of exactly the same length.
The step height of a window handle is also a factor to take into consideration when purchasing an alternative. The step height is the distance from the base of the handle to where it rests on the frame. Typically, this is about 21mm for uPVC windows or 9mm for aluminium. Dropping objects into the gap will let you see how far the handle extends before it comes into contact with an obstruction.
Cockspur handles usually have different backset heights depending on the type of window they are placed in. Inline Espag handles come with an average height of 43mm centre to centre (2 fixing points). Cockspur handles, however have different backset heights depending on the shape of the window they're in. visit the next document is because they have a spur that extends from the handle and is locked onto a cockspur wedge striking plate.
Fit the New Handle
Once you've selected the new handle, ensure that it is aligned with the holes for screws on the door. Then secure it using the screws provided. Install the latch lever in the same way as the main handle in the event that you are replacing the door handle. After that, attach the door trim again to conceal the screws for mounting.
Tips: To remove the metal head from a wooden wedge place the handle on the floor, so that its wide end is on the ground. Then, you can use a hammer and tap the narrow end. Be careful not to damage the handle or the spindle.